setfsb完美版软件(超频处理器)中文版是来自国外的一款非常专业的超频处理工具。该软件功能强大，能帮助你在免进入BIOS控制面板的情况下，快速调整前端总线频率，是各类超频使用用户中经典好用的一款实用型应用工具。推出以来，深受广大的软件爱好者的青睐和喜爱。

Setfsb使用方法

　　Step1
确定PLL芯片的型号
完成诸如电压，内存分频之类的基本参数设置后，我们就可以开始软超频了。
首先需要确定PLL芯片的型号。SetFSB超频的原理和在BIOS里修改参数的原理其实是一样的，
都是通过向PLL芯片发送指令来改变系统总线的频率。
PLL芯片一般可以在主板的PCI-E或PCI插槽附近找到，
标注有如“ICS9*****”“RTM****”“SLG****”“CV1****”等型号字样。
如下图中的这颗Realtek的RTM875T-531。
用SETFSB让菜鸟也能玩转超频
*查找PLL芯片
Step2
在SETFSB软件中找到对应PLL型号
在主板上查看到PLL芯片的型号后，进入setfsb主界面，在第一个“Control”菜单里，
“Clock Generator”右侧的下拉菜单里，选择对应的PLL芯片型号，
比如你主板上PLL芯片上标称的是“RTM875T-531”，就在里面选择“RTM875T-531”。
但如果这个版本的SETFSB发现并没有对应的RTM875T-531，这怎么办呢，
不用着急，我们可以找个相类似的，比如RTM875T-587，因为芯片主型号是相同的，
后面的3个数字不同，只表明芯片存在一点小差异，在setfsb里面还是可以通用的。
用SETFSB让菜鸟也能玩转超频
*找型号相近的也可以
Step3
拖动滑杆即可进行软超频
接下来的工作就简单了，拉动滑动杆，点一下下方的“setfsb”，
此时调整外频至483.5，CPUZ里也正确显示出482.4的外频。
（某些PLL芯片会稍微有一点点误差）这个就可以算作超频成功了。
当然要注意一点，SetFSB里面认到的频率是满倍频的，
降倍频之后的主频要参考CPU-Z中显示的频率。
在必要的时候拉动下面的滑块还可以改动PCI-E频率。
SETFSB非常适合进行极限超频
软超频安全性高，并且不会造成系统无法启动等问题。非常适合用来寻找处理器的极限频率，
当然在超频之前，我们仍然需要在BIOS内对处理器电压，内存分频等进行设置。
而一些没有超频设置的平台，比如笔记本，我们同样能通过软超频来拉升处理器频率。

Setfsb perfect crack version software (overfrequency processor) Chinese version is from abroad a very professional overfrequency processing tools. This software is powerful, can help you in the BIOS control panel without entering the case, quickly adjust the front-end bus frequency, is all kinds of overfrequency users in the classic use of a practical application tool. Since the launch, by the majority of software lovers of all ages.

Setfsb USES methods

Step1

Determine the model of PLL chip

After setting basic parameters such as voltage and memory divider, we can start soft overclocking.

First, we need to determine the model of PLL chip. SetFSB overclocking works on the same principle as modifying parameters in the BIOS,

Both send instructions to the PLL chip to change the frequency of the system bus.

PLL chips can generally be found near the pci-e or PCI slots of the main board.

The labels are as follows: "ICS9*****", "RTM****", "SLG****", "CV1****", etc.

Realtek rtm875t-531 in the picture below.

With SETFSB, newbies can also play overclocking

* find the PLL chip

Step2

Find the corresponding PLL model in the SETFSB software

After checking the model of PLL chip on the main board, enter the main interface of setfsb. In the first "Control" menu,

In the drop-down menu on the right side of "Clock Generator", select the corresponding PLL chip model.

For example, on your motherboard PLL chip is labeled "rtm875t-531", just select "rtm875t-531" inside.

But what if this version of SETFSB finds that there is no corresponding rtm875t-531,

Don't worry, we can find a similar one, such as rtm875t-587, because the main model of the chip is the same,

The latter three Numbers are different, indicating only a small difference in the chip, which can still be used in setfsb.

With SETFSB, newbies can also play overclocking

* look for a similar model

Step3

Drag the slider can be soft overfrequency

The next step is simple. Pull the slider and click on "setfsb" below.

At this time, the external frequency is adjusted to 483.5, and the CPUZ also displays the correct external frequency of 482.4.

(some PLL chips have a slight error.) that counts as overclocking.

It's important to note, of course, that the frequencies that SetFSB recognizes are full multiples,

After frequency reduction, the main frequency should refer to the frequency shown in cpu-z.

You can also change the pci-e frequency by pulling the slider below if necessary.

SETFSB is perfect for extreme overclocking

Soft over frequency security, and will not cause the system can not start and other problems. Very good for finding the limiting frequency of the processor,

Of course, before overclocked, we still need to set the processor voltage, memory frequency, etc. in the BIOS.

On some platforms that don't have overcpus, such as laptops, we can also use soft overcpus to boost processor frequency.